Slow EXE Launch.

[byron.hopp]

I have managed to get it to where it takes 30 seconds to launch my FiveWin / Harbour exe after compile and link. Is it possible I have a bad link / mak file, I'm getting older so it seems like time should be getting faster, or is this typical. Thanks,

[karinha]

VIRUS? Tested on another computer? Use AVG Antivirus. Harbour is much slower than [x]Harbour, but not by much.

¿VIRUS? ¿Probado en otra computadora? Utilice el antivirus AVG. Harbour es mucho más lento que [x]Harbour, pero no mucho.

Regards, saludos.

[byron.hopp]

Can't believe I couldn't put that together. I purchased a new system i9 and all of the Windows Firewall, Virus were on. I have shut them down and it is lightning fast. What is strange is that compiling with xHB (Patrick Mast) it was still fast, only on Harbour was it slow. I will have to play around with settings to find the right balance. Great answer, thanks.

[Rick Lipkin]

Bryon

I use an .EXE shrinker called Aspack .. typically the size of the .exe is at least 30-50 percent smaller .. the smaller the .exe the quicker the program loads .. another benefit of the "shrinker" is that the .exe can not be read with a hex editor that may reveal some of your code ...

Here is the link to review Aspack

http://www.aspack.com/aspack.html

[Carles]

Hi,

put an exception in the antivirus for your folder where your exe is compiled

C.

[Antonio Linares]

Windows Defender (built-in antivirus)

1. Open Windows Defender Security Center.
2. Click on "Virus & threat protection" from the left menu.
3. Click on "Virus & threat protection settings".
4. Under "Exclusions", click on "Add or remove exclusions".
5. Click on "Add an exclusion" and select "Folder".
6. Browse to the folder where your executable is compiled and select it.
7. Click "Add" to add the exception.

[karinha]

Windows Defender (built-in antivirus)

1. Open Windows Defender Security Center.
2. Click on "Virus & threat protection" from the left menu.
3. Click on "Virus & threat protection settings".
4. Under "Exclusions", click on "Add or remove exclusions".
5. Click on "Add an exclusion" and select "Folder".
6. Browse to the folder where your executable is compiled and select it.
7. Click "Add" to add the exception.

VERSION.RC

Code: Select all  Expand view  RUN

1 VERSIONINFO LOADONCALL MOVEABLE DISCARDABLE IMPURE
FILEVERSION 1,0,0,0
PRODUCTVERSION 1,0,0,0
FILEFLAGSMASK 0x0
FILEFLAGS 0x0
FILEOS VOS__WINDOWS32
FILETYPE VFT_APP
FILESUBTYPE VFT2_UNKNOWN
{
 BLOCK "StringFileInfo"
 {
  BLOCK "040904E4"
  {
   VALUE "Comments",    "Sistema Desenvolvido Pela Empresa TAL - www.empresatal.com.br \0"
   VALUE "CompanyName",   "Sistema Desenvolvido Pela Empresa TAL - www.empresatal.com.br \0"
   VALUE "FileDescription", "NOME DO SISTEMA\0"
   VALUE "FileVersion",   "1.0000\0"
   VALUE "InternalName",  "Projeto TAL\0"
   VALUE "LegalCopyright", "Sygecom Informática Ltda\0"
   VALUE "LegalTrademarks", "NOME SISTEMA / SYGECOM\0"
   VALUE "OriginalFilename", "NOME_EXE.EXE\0"
   VALUE "ProductName",   "NOME DO SISTEMA\0"
   VALUE "ProductVersion", "1.0000\0"
  }
 }
 BLOCK "VarFileInfo"
 {
  VALUE "Translation", 0x416, 0x4B0
 }
}
 

Regards, saludos.

[Giovany Vecchi]

I have managed to get it to where it takes 30 seconds to launch my FiveWin / Harbour exe after compile and link. Is it possible I have a bad link / mak file, I'm getting older so it seems like time should be getting faster, or is this typical. Thanks,

Hello I had a similar problem a while ago.
I noticed that fivewin creates a log file with the name of the executable with information about unloaded resources. After a few days this file was huge and when loading the program I noticed that this file was loading and was taking a long time because of its size. I deleted the LOG file and the program opened normally.

[karinha]

Hago siempre asi:

Code: Select all  Expand view  RUN

FUNCTION My_Exit()

   IF FILE( "NAME_EXE.log" )
      DELETEFILE( "NAME_EXE.log" )
   ENDIF

RETURN NIL
 

Regards, saludos.